Ford OBD Codes

2

P1000 Ford

Author: fordobdcodes/Categories: Ford OBD-II Codes/Time: 2013-11-10 09:36
670

Ford P1000 OBD-II Trouble Code Definition:

P1000 OBD system readiness test not complete

P1000 Ford OBD-II Trouble CodeDescription:

OBD Trouble Code P1000
OBD-II Monitor Testing Incomplete

Sorry no other information,Please help us to improve,Any information is appreciated.Thanks.

OBD Trouble Code P1000
OBD system readiness test not complete
What does the code mean? OBD-ii Code P1000 definition:
The OBD monitors are performed during the OBD Drive Mode. The P1000 will be stored in continuous memory if any of the OBD monitors do not complete their full diagnostic check.
Causes Causes of the OBD-II code P1000
? Vehicle is new from the factory ? Battery or PCM had recently been disconnected ? An OBD monitor failure had occurred before completion of an OBD drive mode ? The PCM DTCs have recently been cleared with a M-MDS ? The PCM has been flashed and the vehicle has not yet completed an OBD drive mode.
Solutions

Diagnostic procedure

STEP

INSPECTION

ACTION

1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
???Has the FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY REPAIR INFORMATION AVAILABILITY
???Verify related service repair information availability.
???Is any related repair information available?
Yes
Perform repair or diagnosis according to the available repair information.
If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
CHECK FOR ANY OTHER DTCS
???Where any other DTCs received with the P1000?
Yes
Go to the applicable DTC inspection.
No
Go to the next step.
4
REQUEST TO CLEAR DTC P1000
Note
???A complete OBD drive mode has not yet been performed to clear the DTC P1000 from the PCM.

???Has the customer requested the DTC P1000 be cleared?
Yes
Complete an OBD drive mode, then go to the next step.
No
Inform the customer that if the law in your area required additional driving in order to clear the DTC P1000 from the PCM memory, it must be complete before an inspection/maintenance test.
5
VERIFY THAT DTC P1000 TROUBLESHOOTING IS COMPLETED
???Make sure to reconnect all disconnected connectors.
???Clear the DTC from the PCM memory using the M-MDS.
???Start the engine and warm-up to normal operating temperature.
???Run the vehicle under the FREEZE FRAME DATA stored condition.
???Retrieve the DTC using the M-MDS.
???Is the PENDING CODE same DTC present?
Yes
Replace PCM, then go to the next step.
No
Go to the next step.
6
VERIFY AFTER REPAIR PROCEDURE
???Perform “After Repair Procedure”.
???Is there any DTC present?
Yes
Go to the applicable DTC inspection.
No
Troubleshooting completed.

Mercedes OBD Trouble Code P1000
Electronic Gear Selector Module: Defective N15/5

Sorry no other information,Please help us to improve,Any information is appreciated.Thanks.

Note:

1. We will provide you a definitions and description of Ford vehicle's OBD-II codes.
2. Don't assume a particular Ford OBD Code means the same for other automotive manufacturers as there are many manufacturer specific codes in use.
3. Help us improve Fordobdcode.com. Tell us fix the code. Any information is appreciated. Thanks.

2 comments

  1. Elguja TURMANIDZE /2013-12-24 20:32

    Ford escape 2008 hybrid on the high speed switches the engine and goes on the hybrid drive which is reddened on the screen. Please inform me what,s the problem .? 回应

    #1
  2. fordobdcodesElguja TURMANIDZE comment/2014-02-14 06:04

    from the factory.
    - Battery or Powertrain Control Module (PCM) had recently been disconnected.
    - An OBD monitor failure occurred before completion of an OBD drive cycle.
    - PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool. 回应

    #2

Leave a Reply